How to Replace a Toilet and Connect the Water Lines
To make sure a proper seal is created with the flange and drain, temporarily add the seat and sit on the toilet. The added weight will evenly press the seal tight. Tighten the provided nuts over the closet bolts and tighten.
Line up the flushing valve to the opening in the top of the toilet bowl. After making sure the seal is in place, add the tank to bowl gaskets. Secure the tank with a screwdriver and crescent wrench. New stainless steel supply lines from the ballcock to the stop should be installed.
Now, check for leaks. Add the toilet seat and bolts; adjust the float slider if necessary. Sign up for weekly project ideas and advice from experts. Empty the Tank Turn off the water at the toilet stop by turning the handle clockwise. Disconnect the Tank The first step in actually disconnecting the toilet from the bathroom is to unscrew the supply line from the stop using a crescent wrench.
Remove the Bowl Flip up the bolt covers and remove them if necessary. Replace the Wax Ring The next step is to take an ordinary putty knife and scrape off the old wax ring Image 1. Create a Seal Line up the closet bolts with the bowl and gently let down the bowl. Align the Flushing Valve Line up the flushing valve to the opening in the top of the toilet bowl. Finish the Installation New stainless steel supply lines from the ballcock to the stop should be installed. How to Remove and Replace Grout 3 Steps. How to Replace a Window 7 Steps.
How to Replace a Bathroom Vanity 10 Steps. Empty the Tank Step 2: Disconnect the Tank Step 3: Remove the Bowl Step 4: Replace the Wax Ring Step 5: Create a Seal Step 6: Align the Flushing Valve Step 7: Bargain Mansions 7am 6c. Bargain Mansions 8am 7c. Bargain Mansions 9am 8c. Bargain Mansions 10am 9c.
Bargain Mansions 11am 10c. Bargain Mansions 12pm 11c. Rehab Addict 1pm 12c. Rehab Addict 2pm 1c. Rehab Addict 3pm 2c.
How to Install a Water Connection for a Toilet | Home Guides | SF Gate
Rehab Addict 4pm 3c. Rehab Addict 5pm 4c. Sometimes the leak gets worse.
Never try to tighten a leaking line with just one wrench. This is especially true when the fittings are old and corroded. Use two wrenches, one on the fitting you are tightening and the other on the valve or pipe you are tightening to. For small leaks you can try tightening the fittings. Be careful and don't over tighten. Too much torque and you can make things worse, a little leak becomes a big leak. Go a quarter turn at a time and check to see if it is still leaking.
Dry the fitting off with a rag and rub you finger across it. A dry finger should mean no leaks. If the toilet water supply line is too corroded you will need to replace it. Shut the water off at the water shut off valve. Is the valve old and corroded to? With the water off you will want to loosen the fittings. The two wrench thing applies even when you are removing the old one. Two things you have to do with the supply line. First you have to shape it to the right bends. Use a tubing bender or your thumbs to carefully bend the pipe.
Dry fit the tubing to the flange on the toilet and mark the length to cut it. Use a hack saw to cut the tubing to length. Get a new nut and ferrule for the end that goes into the valve and a large nut for the closet connection.
How to Install a Water Connection for a Toilet
Make sure the supply line you buy is for a toilet and not a sink, they are different. Put the nut, then the ferrule on the line and start the tubing into the valve. Turn the nut finger tight. Put the nut on the toilet and tighten finger tight. Tighten them down if you are sure they fit. Turn the water back on and check for leaks.
A more popular choice in recent history is a flexible line with factory installed fittings. Since the line is flexible you can move it as needed for proper alignment. The fittings screw onto the valve and toilet tank without any additional parts. Simple, less than ten minutes to install one of these.
- dating adirondack bats?
- Be Careful.
- Toilet Supply Line Leaking.
- how down dating app works.
- Types of Toilet Water Supply Lines.
Toilet water supply lines come in two styles. Plastic lines are less expensive and are usually white. Stainless steel lines cost a little more. The steel lines are still flexible and are a little tougher. Flexible toilet supply lines have factory installed ends on them.
These ends have integral washers built into them, so they are ready to go. The likely problem with this type of line is a leak at one of the fittings. Tightening them up is usually the solution. A flexible toilet water supply line is a little easier to tighten.