Pool equipment hookup

How to Hook Up a Swimming Pool Filter

For more information on valves click here. Step 10 This picture shows a common valve setting for this pool. The yellow "T" lines placed over each valve show the position of the valve handles. If the handle is placed so that the top of the "T" is across a pipe, that port is closed - as is the case for the pool cleaner and the spa drain. If the handle is placed with the top of the "T" running in line with the pipe, all ports are open.

If the "T" is at an angle to the pipe, the valve is allowing partial flow through the port - as is the case with the pool drain. In this particular valve configuration water is flowing to the pump from the two skimmers and partially from the pool drain. Water from the spa drain and the pool cleaner is blocked. When the suction cleaner is used, the skimmer ports are shut off to provide more suction to the cleaner.

How to Hook Up a Swimming Pool Filter | ovahiryripen.tk

Step 11 "To Pool" - The second half of this guide discusses the discharge side of the pump - water being pushed from the pump, through the filter, and back to the pool. Step 12 Water is discharged from the pump into the pool filter. Step 13 After the water is filtered, it flows to a valve that diverts the water through a heater loop if desired. If not, the valve is set to have the water bypass the heaters and flow directly to the system chemical treatment equipment.

The yellow "T" superimposed on the valve shows that the valve is set to divert the water through the heater loop. See Part 3 for an expanded discussion of this pool's Heaters. Step 14 This pool system uses a fully automated chemical system to control the chlorine and pH levels. See Part 4 for an expanded discussion of the Chemical equipment. Note that a check valve has been inserted just before the Chlorinator.

This valve only allows the water to flow in one direction. Sometime when the pumps is shut off, backpressure is created that may push the water backwards. This valve keeps the undiluted chlorine water from backing up into and damaging the heater and filter systems. Step 15 From the Chlorinator the water flows to a series of diverter valves that direct the water to the various return ports in the pool. Note the Flow Gauge inserted in the pipe just before the diverter valves. Or give us a call at , and we would be happy to take your order by phone.

Step 1 Before starting installation, you will need to purchase sand. Use only high rate No. An example is pictured at left. Check the manufacturer to determine the amount required. This unit Hayward ST uses 3 50 lb bags of sand - lbs total. You can also purchase our superior to sand Click here for our Sand Alternative.


  • ?
  • .
  • dating agency cyrano 2013 asianwiki.

Step 2 When installing the pool sand filter, you will connect it right after the pump. Pool water will come in through the pool pump, be filtered through the sand filter and released to the chlorinator before returning back to the pool. If you have a pool heater, the pool filter will release water to the heater before going to the chlorinator.

Step 3 The pool filter should be installed on a level concrete slab not more than 6 feet above the pool water level. Position the pool sand filter so that the piping connections, multiport valve and drain are convenient and accessible for operation and maintenance. Place the filter next to pump. Step 4 Before you connect the pool sand filter into the piping system, you have to assemble the filter.

If the threads aren't prepared, wrap them with two layers of Teflon tape. Start in a clockwise direction at the first thread with a half width overlap for the full length of the thread. Be careful when screwing the gauge on. Use a wrench on the square nut on the final turns. Step 5 Make sure drain cap is securely in place.

Tips On How To Install Swimming Pool Equipment

This will help protect the laterals. Step 7 Next you will be installing pipe and lateral assembly inside the tank. Separate the valve from the pipe and lateral assembly. Also make sure the 10 laterals at the end of the pipe are rotated up. They have to be in their up position to fit through the hole in the top of the tank. These laterals are somewhat fragile.

How To: Install a Top Mount Pool Sand Filter

Ensure that none are cracked or broken. Place the pipe and lateral assembly inside the tank. Step 8 After the lateral assembly is inside, carefully rotate the 10 laterals 90 degrees in their down position. Step 9 Make use the pipe is centered in the opening.

Tape the top of the pipe to prevent sand from entering and clogging the laterals. Step 10 The sand filter package comes with a cardboard sand shield. Place this over the pipe and within the opening. Step 11 Pour sand carefully into the pool sand filter until laterals are fully covered.

For this unit 3 bags should leave at least 6" space between the top of the sand and the top of the filter. Level sand as you pour and make sure the center pipe remains centered in the opening. Be careful when leveling the sand that you do not lift the pipe and lateral assemble up off the bottom of the tank. You will not be able to push the pipe back down without causing the laterals to rotate up. Step 13 Remove tape from top of pipe. Slip the Multiport control valve onto the central pipe - check the O-ring to ensure it is positioned correctly.

Step 14 Install clamp around the tank and valve flange. To keep from cracking or damaging the hose, do not over-tighten the clamp. Finally, make sure that your filter pumps power supply is grounded as it should be.

How To Set Up In Ground Pool Equipment - Part 1 - Circulation

Keep in mind that even with a filter, you will still have to manually clean your in-ground pool—especially if it is located by a lot of trees or bushes. Be sure to empty your skimmer basket weekly and use a net to dispose of excess bugs and leaves. Vacuum your pool and scrub the walls from top to bottom. Add chlorine for sanitation. Keeping up with your pool will keep it from draining energy your entire summer.