Hook up av receiver

Very simply, this is where you send a video signal from the receiver out to your TV. By the way, we apologise for not being able to tell you exactly how to connect up your individual units. In the same way as the previous section, just run a video cable from the Monitor out to your TV.

Some receivers come with additional ports allowing you to collect multiple monitors the zone 2 on the back of our Marantz which is always handy. The problem with home theater manufacturers is that they have to take into account every eventuality. Hence, the presence of component video ports, a technology that is to modern home entertainment what the penny farthing is to road cycling. Component video cables split the signal into three separate colour components, which is why they are triple headed monsters. Connecting them is easy enough — just line up the colors. Just connect the Out ports of your player to the In ports of your receiver.

And remember, component video just carries video. Same here as for the video out above.

How to Connect a Cable Box and an AV Receiver to HDTV | It Still Works

Another very straightforward connector. If your receiver has the ability to link up with your home network, or stream on Bluetooth as this Marantz does then this is where you will attach the antennae that comes with the unit. If your wireless network is sketchy, then you can use this to connect directly to your route with an ethernet cable. Ethernet cables are easily identifiable, and simple to use.

Essentially, it allows you to trigger another device when you switch on the receiver.

Can a Soundbar work with a Receiver?

The best example we can think of is to have a projector screen automatically lower itself when you turn the receiver on. A word of caution. Make sure the input and output voltages on each device match. You should be able to find them in the respective manuals. Instead, you use the multi-pin, locking cable to connect things like PCs, or external touchpads for controlling the on-screen action. It means you can also automate the system to, say, turn on and off at a particular time.

Well, this port allows you to use a better one. By buying something known as an IR flasher or blaster , you can connect it up to this particular port and control the receiver using the remote of your choice. This is for turntables. Without getting too technical about it, a turntable without its own preamp will need to be electrically grounded, otherwise you risk getting an unpleasant humming sound. This port fixes that, allowing you to attach an external receiver that can communicate with your remote.

Still, good to have.

How to Connect Speakers to Amplifiers - Home Audio Basics

We spent a long time tinkering with Photoshop graphics and setup photos, trying to communicate just how best a system can be connected. In the end, we've gone for simplicity over everything else. Connecting a system and getting things right can be a giant pain in the backside, so we decided to make things as simple as possible, with a few straightforward tips and a set of components that we think most people will either have, or have something close to. You need to leave a bit of space around them to make sure that they have enough ventilation.

If you have to put them in a cabinet, try making sure the space around them is clear. Make sure you have all the correct cables. This includes speaker wire — and when it comes to speaker wire, there are two things you can do to make your life easier. Always give yourself an extra few yards, and then make the cut when you're absolutely sure where you're going to place a particular speaker, and label each cable.

Not just the positive and negative lines we use a black sharpie on each side to indicate the negative wire but also what each cable is driving left front, right front, subwoofer etc. The PlayStation and the TV are the easiest. Each speaker, with the exception of the subwoofer, is going to be connected to the binding posts by a single wire, split at both ends. Red connects to red, and black to black. The labelling should be pretty self-explanatory — we connect the two tower speakers to the Front Left and Front Right posts, the centre speaker to the Centre post, and so on.

Only one last thing to do, which is to connect the subwoofer.

You'll be enjoying cinematic sound in no time

We don't need to send power to the subwoofer, as it has its own amp. All we need to do is send an audio signal to it, which we do by connecting the RCA cable to both the sub and the dedicated Sub Out ports on the Pre Out section. And in terms of connection, that's it! Obviously, things can be a lot more complicated — we haven't even touched on things like multizone setups, or adding other amplifiers to the mix.

But as a general principle, this will get you started. The last thing you need to do is calibrate the system. The Marantz actually includes a fantastic room calibration set up with an included microphone, but even if your receiver doesn't offer this, it should offer a relatively comprehensive on-screen menu that allows you to set things like the subwoofer crossover, and the number and size of your speakers, to optimise the sound. If, by the way, you want to know more about things like subwoofer crossover, check our Ultimate Guide To Subwoofers!

As we said in our review , we said, "This is a flagship receiver. Very affordable, with superlative sound and good features, including Bluetooth streaming. Watch out though - it only has four HDMI ports. We'd say you should go for this one if you need a simple, straightforward 5. Cut appropriate lengths of wire to run from the receiver to each speaker.

Make sure to leave enough slack if you want to neatly dress the cables after they're connected. Strip about a half-inch of insulation from the end of each individual wire the speaker wire has two insulated wires fused together. Twist the exposed wire to keep the strands from fraying in their connections. Push down the tab of the spring clip connector or unscrew the binding post connector of the terminal is on the back of your receiver. Secure the exposed ends on the speaker end of the wire to the terminals on the back of the speakers as necessary.

Make sure to match positive to positive to positive and negative to negative to avoid sound reproduction issues and damage to your speakers. Adam Hilton is an Austin-based sound designer and engineer who has been writing professionally since He has won and been nominated for multiple awards for his theatrical sound design and compositions, including the B.

Tip You can reinforce your speaker wire connections by using connectors instead of just the bare wires.


  • Here are some of the top soundbars available at Best Buy in 2018:?
  • soirée speed dating genève;
  • what to do when you start dating a guy.
  • How to Connect Speakers to an AV Receiver | It Still Works.
  • 18 year old 25 year old dating.
  • radiocarbon dating water.
  • A/V Receiver Setup Explained | The Master Switch.

Pin, spade, and banana plug connectors are all available from audio electronics retailers and can be easily added to the ends of your speaker cables. Warnings If your receiver has outputs for line-level signal, such as for a subwoofer or additional surround channels, you will need an external amplifier to boost the line signal.